23
2024
12
Common Faults of Electric Actuators and Their Root Cause Analysis
Electric actuators are widely used in industrial automation control systems, performing the switching and regulating functions for valves, dampers, regulators, and other equipment. Thanks to their high efficiency and precision, they play a critical role in numerous sectors, including chemical processing, metallurgy, power generation, and water treatment. During prolonged operation, electric actuators inevitably encounter various malfunctions; these issues not only reduce production efficiency but can also lead to equipment downtime, process interruptions, and even safety incidents. Consequently, promptly identifying and addressing actuator faults is essential for ensuring stable and reliable equipment performance.
1.1 Common Types of Faults in Electric Actuators
There are numerous types of malfunctions in electric actuators; the most common include the following:
The electric actuator fails to operate or operates abnormally.
This type of malfunction typically manifests as the actuator’s inability to perform opening or closing operations as specified, or as imprecise movement. For example, a valve may fail to fully open or close, resulting in unstable fluid flow and adversely affecting the production process.
Actuator overheating
Overheating of the actuator can lead to equipment failure and loss of control. Such overheating may result from prolonged operation of the motor under overload, inadequate lubrication, excessive load, or other causes.
Motor fails to start or trips frequently.
When an electric motor fails to start properly or trips frequently during operation, it is often attributable to faults in the electrical system, unstable supply voltage, or damage to the motor itself.
Control system failure
A malfunction in the control system of the electric actuator may prevent the control signal from reaching the actuator, thereby disabling normal operation of the equipment.
Mechanical components are jammed or worn.
Mechanical transmission components within the actuator—such as gears, bearings, and lead screws—can experience wear, aging, and seizing after prolonged operation; in severe cases, this may result in equipment shutdown.
1.2 Analysis of the Causes of Electric Actuator Failures
The causes of malfunctions in electric actuators can be analyzed from the following aspects:
1.2.1 Electrical System Issues
Electric actuators typically rely on electrical control systems to transmit signals and supply power. If the electrical control system malfunctions, the actuator may fail to operate properly. Common electrical issues include:
Power supply issues: Voltage fluctuations, power outages, or an unstable power source can prevent the actuator from receiving sufficient power to operate.
Control signal anomaly: If the control signal is distorted or the transmission is interrupted, the actuator may fail to receive the correct operating command.
Motor failure: Issues such as short circuits or open circuits in the motor windings, or the activation of overload protection, can prevent the actuator from operating properly.
1.2.2 Mechanical System Issues
The mechanical components of an electric actuator constitute the core of its motion transmission, and any mechanical issue can lead to abnormal equipment operation. Common mechanical problems include:
Poor lubrication: Prolonged lack of lubrication, or the use of low‑quality lubricant, can increase friction between mechanical components, leading to wear or seizing.
Gear and bearing wear: After prolonged use, critical components such as gears and bearings experience wear, reducing transmission efficiency and potentially rendering the equipment inoperable.
Overload: If the actuator’s load exceeds its design capacity, mechanical components are prone to damage, resulting in abnormal operation.
1.2.3 External Environmental Influences
The external environment also significantly affects the performance of electric actuators. For example, excessively high or low temperatures, humidity, and dust can all damage the actuator’s electrical and mechanical systems.
High-Temperature Environment: Prolonged operation in high-temperature conditions can cause the motor of an electric actuator to overheat, triggering overload protection or resulting in damage.
Moisture and Corrosion: In high-humidity environments, electrical components of equipment are prone to short circuits or corrosion, compromising their normal operation.
1.2.4 Design and Installation Issues
Design flaws or improper installation of electric actuators can also lead to operational malfunctions. For example:
Mismatched components: If the motor, transmission system, and load of an electric actuator are not properly matched, it may result in overload or overspeed, ultimately leading to equipment damage.
Improper installation location: If the equipment is installed in a location subject to significant vibration, poor ventilation, or difficult access for maintenance, its service life may be shortened.
1.3 Preventive Measures for Electric Actuator Failures
To effectively reduce failures in electric actuators, prevention is of paramount importance. Enterprises can implement the following measures:
Regular Maintenance and Inspections: Conduct routine inspections of electric actuators, with particular attention to the electrical system, mechanical components, and lubrication system, to ensure the equipment remains in good working condition.
Environmental Control: When installing electric actuators, select appropriate environmental conditions to prevent damage caused by moisture, high temperatures, and severe vibrations.
Proper selection and installation: Select equipment appropriately based on actual operating conditions to ensure proper matching between the actuator and the load, and install it in accordance with relevant standards.
Employee Training: Strengthen training for operators to enhance their ability to diagnose equipment malfunctions, enabling timely resolution of minor issues and preventing large-scale equipment damage.
Through effective preventive measures and routine maintenance, the likelihood of failures in electric actuators can be significantly reduced, thereby ensuring the stability and safety of the production system.
Methods and Solutions for Troubleshooting Electric Actuators
When an electric actuator malfunctions, timely and effective fault diagnosis and troubleshooting are crucial. Different types of faults require distinct corrective measures; the following outlines common fault-handling procedures and solutions.
2.1 The electric actuator fails to operate or operates abnormally.
If the electric actuator fails to operate or operates abnormally, the following aspects should be checked first:
2.1.1 Check the power supply
Ensure that the power supply voltage to the electric actuator is stable and meets the equipment’s specifications. If a power supply failure occurs, promptly repair or replace the power supply unit.
2.1.2 Inspection of the Control System
Verify that the control signals are functioning properly and ensure unobstructed signal transmission from the control system to the actuator. If the control signals are abnormal, inspect the control circuitry or replace any damaged components.
2.1.3 Inspect the motor and transmission components
Check that the motor is operating normally, verifying that its voltage, load, temperature, and other parameters remain within acceptable limits. If the motor is overloaded or malfunctioning, it must be replaced or repaired. Inspect the actuator’s transmission components for jamming, wear, or damage, and lubricate or replace them as necessary.
2.2 Actuator Overheating
If the electric actuator overheats, it may be due to motor overload, insufficient lubrication, or excessively high ambient temperatures. The recommended troubleshooting steps are as follows:
2.2.1 Check the load condition
Confirm whether the actuator’s load exceeds its design limits; if necessary, adjust the load or select an appropriately rated actuator model.
2.2.2 Enhance Lubrication
Inspect the internal lubrication system of the actuator to ensure adequate lubricant levels and good oil quality. For equipment that has not been lubricated for an extended period, perform a thorough cleaning and replenish with high‑quality lubricant.
2.2.3 Reducing Ambient Temperature
If the equipment is exposed to high-temperature environments for extended periods, it is recommended to apply thermal insulation or consider installing an improved cooling system to ensure the equipment operates within an appropriate temperature range.
2.3 Motor failure to start or frequent tripping
Motor starting failures or frequent tripping are typically attributable to faults in the power supply, the load, or the motor itself. The recommended troubleshooting steps are as follows:
2.3.1 Check the power supply voltage
Ensure that the power supply voltage is stable and within the equipment’s specified range. If the voltage is unstable, a voltage stabilizer can be installed to protect the equipment.
2.3.2 Check the motor load
Verify whether the motor’s load exceeds its rated capacity. If the load is excessive, reduce it or replace the motor with one that matches the required specifications.
2.3.3 Inspect the motor condition
Inspect the motor to determine whether there is a short circuit, overload, or overheating. If the motor is damaged, replace it promptly.
2.4 Mechanical component jamming or wear
When mechanical components become jammed or worn, disassembly and maintenance are typically required. Possible solutions include:
2.4.1 Cleaning and Lubrication
Thoroughly clean all mechanical components and inspect the lubrication system to ensure proper operation. Add or replace lubricant as needed to guarantee smooth performance of all parts.
2.4.2 Replacement of Worn Components
For components that are severely worn or damaged, such as gears and bearings, they should be replaced promptly, and the new parts should be properly lubricated.
2.4.3 Load Adjustment
If the actuator is subjected to an excessive load, resulting in accelerated wear of its mechanical components, the load should be adjusted accordingly to prevent over‑operating the mechanism.
2.5 Control System Failure
The methods for handling control system malfunctions include:
2.5.1 Inspect Control Signals and Wiring
Inspect all control signal lines to ensure they are intact and that signals are transmitted properly. If any damage is detected, the affected lines should be replaced immediately.
2.5.2 Inspection of Control Components
If control components (such as relays, sensors, etc.) are damaged, they should be replaced promptly.
2.5.3 Calibration Procedure Settings
If the issue lies with the programmable control system, verify that the program settings are correct and reprogram the system if necessary.
2.6 Conclusion
Troubleshooting and maintenance of electric actuators are critical tasks for ensuring the efficient and stable operation of equipment. Timely fault diagnosis and scientifically sound repair procedures can effectively extend equipment life and reduce maintenance costs. Industrial equipment managers should conduct regular inspections and maintenance of electric actuators to guarantee the safe and reliable operation of production systems.
Electric actuators, fault troubleshooting, equipment maintenance, industrial automation, valves