04
2025
01
Common Faults and Troubleshooting Methods for Electric Actuators

In modern industrial automation, electric actuators are indispensable components of control systems, widely employed in various mechanical systems to regulate valves, control fluid flow, and adjust temperature, among other functions. Given that electric actuators operate continuously over extended periods and are subject to diverse environmental factors, malfunctions are inevitable. To ensure reliable equipment performance, it is crucial to understand common actuator failures and their corresponding troubleshooting methods.
I. Analysis of Common Faults in Electric Actuators
The electric actuator fails to start or operates abnormally.
When an electric actuator fails to start or exhibits abnormal behavior during operation—such as failing to reach its intended position or moving sluggishly—it is often due to power supply issues, motor malfunctions, or problems with the control signal. Electric actuators typically rely on motor-driven operation; if the supply voltage deviates from its normal range, the actuator will be unable to start or function properly.
Cause Analysis:
Excessive power supply voltage fluctuations or undervoltage prevent the electric actuator from receiving proper power.
The motor inside the electric actuator has malfunctioned, such as burning out, experiencing an open circuit, or suffering brush wear.
An abnormality in the control signal input has prevented the actuator from receiving the correct start-up signal.
Handling method:
Check the supply voltage to ensure it meets the rated voltage requirements of the electric actuator.
Regularly inspect the motor of the electric actuator, and promptly replace or repair it if any damage or aging is detected.
Inspect the control signal system to verify that the control signals are functioning properly and ensure that all connecting cables are securely fastened.
The actuator’s movement is inaccurate and fails to reach the intended position.
This is a common malfunction in electric actuators, manifesting as sluggish operation, positional deviation, or an inability to achieve precise control. Typically, such failures are caused by issues with the actuator’s positioning system—such as the encoder—or by damage to mechanical components.
Cause Analysis:
A sensor malfunction inside the electric actuator is preventing accurate position feedback.
Wear of internal mechanical components, such as gears and bearings, results in imprecise motion.
Improper control system parameter settings or software errors prevent the actuator from accurately executing commands.
Handling method:
Inspect and calibrate the positioning system of the electric actuator, including encoders and sensors, to ensure proper operation.
Regularly inspect mechanical components for wear and perform lubrication or replacement as needed.
Re‑commission the control system, verify that the parameter settings are correct, and ensure system stability.
Excessive heating of the electric actuator
Excessive heating of an electric actuator can lead to equipment damage or reduced operational efficiency. This type of failure is typically caused by excessive motor load or inadequate heat dissipation.
Cause Analysis:
The electric actuator has been operating under high load for an extended period, exceeding its rated operating range.
There are issues with the internal cooling system of the electric actuator, such as a damaged cooling fan or blocked heat sinks.
The electric actuator is operating in an excessively harsh environment, resulting in excessively high operating temperatures.
Handling method:
Check the operating load of the electric actuator to prevent prolonged operation at full load; if necessary, implement appropriate load sharing.
Regularly inspect the electric actuator’s cooling system to ensure that components such as the cooling fan and heat sinks are functioning properly.
Improve the operating environment to prevent adverse conditions such as high temperature, high humidity, or dust from affecting the equipment.
The electric actuator responds slowly.
When the response speed of an electric actuator slows down, it can adversely affect the efficiency of the entire production line, particularly in industrial applications that demand high precision. The causes of such malfunctions are varied and typically involve the electrical system, mechanical transmission components, or the control system.
Cause Analysis:
A fault in the electrical components of the electric actuator has resulted in poor signal transmission and sluggish response.
Mechanical components experience jamming or increased friction, resulting in impaired motion.
A malfunction in the control system or software program prevents timely transmission of control commands.
Handling method:
Inspect the electrical components, paying particular attention to the connection status of cables, connectors, sensors, and other parts, to ensure unimpeded signal transmission.
Inspect the mechanical components, remove accumulated dust, lubricate moving parts, and ensure smooth operation of the mechanical transmission.
Perform a troubleshooting check on the control system, verify the program settings, and ensure that control signals are timely and accurate.
II. How to Prevent Failures in Electric Actuators
In addition to promptly addressing faults once they occur, we can also reduce the incidence of electric actuator failures through systematic management and maintenance, thereby enhancing equipment efficiency and extending its service life.
Regular Maintenance and Inspections
Regular maintenance and inspections of electric actuators are an effective way to prevent failures. By routinely examining the actuator’s electrical, mechanical, and control systems, potential fault risks can be identified early, enabling timely repairs and component replacements.
Specific measures:
Inspect the electric actuator’s electrical system monthly to ensure a stable power supply and that cables and connectors are secure and undamaged.
Inspect the wear of mechanical components quarterly, and promptly lubricate or replace any worn parts.
Conduct a comprehensive inspection of the control system every six months to ensure that control parameters are correct and signal transmission is smooth.
Selecting Electric Actuators Appropriately
When selecting an electric actuator, it is essential to choose the appropriate model based on the specific application requirements. An improper selection may result in the actuator operating under excessive load, potentially leading to malfunctions.
Key considerations for selection:
Select electric actuators that are suitable for the load and operating environment to prevent equipment failure caused by excessive loads or harsh working conditions.
Consider the service life, maintainability, and adaptability of electric actuators in special environments.
After selecting the appropriate model, ensure proper installation and commissioning to guarantee that the electric actuator operates under optimal conditions.
Ensure the stability of the operating environment.
The operating environment of an electric actuator has a critical impact on its performance. Environmental factors such as temperature, humidity, and dust can all affect the actuator’s operational stability. Therefore, it is essential to ensure that the electric actuator is housed in a stable, clean environment whenever possible.
Environmental Management Measures:
Avoid installing electric actuators in environments with high temperatures, high humidity, or a high concentration of corrosive gases.
Regularly clean accumulated dust around the electric actuator to ensure unobstructed heat dissipation pathways.
Equip electric actuators with appropriate protective enclosures to prevent dust, moisture, and other contaminants from entering the equipment.
Personnel Training and Operating Procedures
The skills and experience of operators directly affect the performance of electric actuators. By enhancing operator training to improve their understanding of and proficiency in operating electric actuators, it is possible to effectively reduce failures caused by improper operation.
Training Highlights:
Conduct training on equipment operation and maintenance to ensure that operators can perform the correct procedures when handling electric actuators.
Develop personnel’s ability to diagnose faults in electric actuators, enabling them to promptly identify and address potential issues.
Regularly organize technical exchanges to share operational and maintenance expertise, thereby enhancing the team’s overall skill level.
III. Summary
As an essential component of modern industrial automation, the troubleshooting and preventive maintenance of electric actuators are critical to ensuring the smooth operation of production lines. Understanding common failure causes and corresponding solutions, conducting regular maintenance and inspections, selecting appropriate electric actuators, and maintaining a stable operating environment can all effectively prevent malfunctions and ensure the long-term, reliable performance of equipment. Through systematic management and meticulous upkeep, you can significantly enhance equipment efficiency, extend its service life, reduce maintenance costs, and boost overall production productivity.
Electric actuators, common faults, troubleshooting, equipment maintenance, electric actuator servicing
Previous page
Previous page